VIN / Build Split
VIN pos 4-8 identifies model/trim/engine/restraint. Genesis WMI: KMT. Position 4-5 = model. Position 10 = model year code.
3,200+ Vehicles Supported
1-Year Unlimited Guarantee
DFW Mobile Service
DFW Serving Dallas / Fort Worth
2019 Genesis G70 Supported Services
2019 Genesis G70
ADAS calibration, module programming, and security relearns
Multiple trim levels available. ADAS feature availability varies by trim and options package. Contact us for specific trim calibration requirements.
Technical snapshot
- Platform IK (Genesis G70 / Kia Stinger shared RWD platform)
- CAN Architecture Hyundai/Genesis CAN bus (HS-CAN, MS-CAN, LIN for body subsystems)
- Security Genesis IMMO4 - pin extraction available via GDS2 dealer auth; AKL supported
What do you need fixed?
Choose a service to start your quote.
OVERVIEW
Expert ADAS calibration, module programming, and diagnostic recovery for the 2019 Genesis G70. On this vehicle we cover documented systems include Forward Collision-Avoidance Assist (FCA) - Front Camera, Forward Radar (77GHz), and Blind Spot Detection (BSD) - Rear Radar, this IK (Genesis G70 / Kia Stinger shared RWD platform) platform vehicle, IMMO4 immobilizer support, Genesis Connected Services infotainment programming. Mobile across the DFW Metroplex; mail-in module service is available nationwide.
Platform
IK (Genesis G70 / Kia Stinger shared RWD platform)
Production
2019-present
Trim Levels
Multiple trim levels available. ADAS feature availability varies by trim and options package. Contact us for specific trim calibration requirements.
Drivetrain
RWD / AWD
Engine
-
CAN Speed
Hyundai/Genesis CAN bus (HS-CAN, MS-CAN, LIN for body subsystems)
YEAR-SPECIFIC NOTES
Infotainment
Genesis Connected Services
Exact-year service summary for 2019 Genesis G70
ADAS coverage
This 2019 Genesis G70 page documents 5 ADAS systems, including Forward Collision-Avoidance Assist (FCA) - Front Camera, Forward Radar (77GHz), Blind Spot Detection (BSD) - Rear Radar, and Lane Keeping Assist (LKA).
View ADAS dataCalibration triggers
Documented calibration triggers include Windshield Replacement, Front Bumper Repair or Replacement, Rear Bumper Repair or Replacement, and Any Collision. Use the ADAS tab for the full trigger list.
View triggersProgrammable modules
This page indexes 15 programmable module records across SRS, ECU, BCM, TCU/TCM, ABS, and IPC coverage.
View modulesGateway and security
This page includes 2 gateway, immobilizer, or key-security records for this 2019 Genesis G70.
View securityCore Auto Logic capability
Core Auto Logic supports exact-year diagnostics, ADAS calibration, module programming, and security-access planning for the 2019 Genesis G70 using the documented systems and module data on this page.
Choose a sectionWhat changes on this exact year
Feature availability
Genesis Advanced Safety: Forward Collision Alert, Lane Keeping Assist, Driver At - Available; Platform: IK (Genesis G70 / Kia Stinger shared RWD platform) - Confirmed
Driver-assist suite
Genesis Advanced Safety: Forward Collision Alert, Lane Keeping Assist, Driver Attention Warning, Blind Spot Detection, Smart Cruise Control, Rear Cross-Traffic Alert
VIN and build split
VIN pos 4-8 identifies model/trim/engine/restraint. Genesis WMI: KMT. Position 4-5 = model. Position 10 = model year code.
Infotainment context
Genesis Connected Services; Genesis Connected Services AVN; 8-inch display; Apple CarPlay / Android Auto
Network and access
CAN: Hyundai/Genesis CAN bus (HS-CAN, MS-CAN, LIN for body subsystems)
Tool access for this exact year
Representative tool access paths for this exact model year, gated by the vehicle data and source packet we currently trust.
Factory scan, coding, and calibration access
Hyundai GDS Mobile / Hyundai KDS
Factory routines and secure server authorization control this path when aftermarket coverage is not enough for the VIN.
ADAS scan, setup, and verification
Autel, Launch Tech, Topdon
Used where aftermarket coverage supports the procedure; OEM software remains required for locked factory routines.
Bench cloning and chip-level recovery
Alientech / Autotuner / Orange5 / Scanmatik / Flex / VVDI2 / PCMFlash / CGDI / X-Prog
Used only when the module, donor data, EEPROM, MCU, or crash-data workflow requires bench or chip-level handling.
Bench/chip-level only
Choose a section to view data
SUPPORTED SYSTEMS
What we service on this vehicle
Documented module coverage for the 2019 Genesis G70. Counts reflect modules our techs have programmed or calibrated on this exact platform.
ADAS Calibration
5 modules documented
Forward camera, radar, surround-view and lane-keep recalibration after windshield, suspension or fascia work.
Open ADAS tabEngine / ECU Programming
2 modules documented
Powertrain reprogramming, calibration updates, replacement ECU configuration and security access.
Open Modules tabBCM / Body Programming
1 module documented
Body control module, gateway and accessory programming. Includes feature-bit reconfiguration.
Open Modules tabTCU / Transmission
1 module documented
Transmission control module reprogramming, adaptive learning reset and replacement TCM clone.
Open Modules tabSRS / Airbag Reset
3 modules documented
Crash-data clear, hard-code reset and replacement airbag module configuration.
Open Modules tabABS / Brake Module
1 module documented
ABS / EBCM bleed support, replacement module coding and yaw-rate sensor calibration.
Open Modules tabIPC, SAS & Other Modules
4 modules documented
Instrument cluster cloning, steering angle sensor calibration and other supporting modules.
Open Modules tabConnectivity & Accessories
3 modules documented
Infotainment radio, surround view, remote start, trailer brake controller and other equipped systems.
Open Modules tabRecalibration Triggers
8 modules documented
Service events that require ADAS recalibration on this vehicle. Tap to see what triggers what.
Open ADAS tabNeed something not listed? Most undocumented modules can still be programmed.
Get a QuoteFeature availability 2
Genesis Advanced Safety: Forward Collision Alert, Lane Keeping Assist, Driver At
AvailableCalibration required after windshield replacement, camera/radar service, or structural repair affecting sensor alignment.
Platform: IK (Genesis G70 / Kia Stinger shared RWD platform)
ConfirmedVerify platform code matches when cross-referencing part numbers across model years.
WHAT WE RESOLVE
Common issues on this vehicle
Common Genesis G70 issues we resolve on this platform: Forward Collision-Avoidance Assist (FCA) - Front Camera, Forward Radar (77GHz), Blind Spot Detection (BSD) - Rear Radar, and Lane Keeping Assist (LKA) recalibration after windshield/bumper/suspension/CCM service. Module programming for replacement ECU/PCM, BCM, TCU, or accessory modules - IK (Genesis G70 / Kia Stinger shared RWD platform) platform uses Hyundai/Genesis CAN bus (HS-CAN, MS-CAN, LIN for body subsystems).
ADAS CALIBRATION MATRIX
ADAS systems on this vehicle
Genesis Advanced Safety: Forward Collision Alert, Lane Keeping Assist, Driver Attention Warning, Blind Spot Detection, Smart Cruise Control, Rear Cross-Traffic Alert
Scroll for part numbers and Details
| System | Type | Category | Cal. Type | Supported | Part # | Actions |
|---|---|---|---|---|---|---|
| Forward Collision-Avoidance Assist (FCA) - Front Camera | Forward Camera | Camera | Static | YES | ~99210-G9000 (VERIFY VIA OUR DIAGNOSTIC SOFTWARE) | |
| Forward Radar (77GHz) | Front Radar | Radar | Static | YES | ~99110-G9000 (VERIFY VIA OUR DIAGNOSTIC SOFTWARE) | |
| Blind Spot Detection (BSD) - Rear Radar | Side Radar | Radar | Static + Dynamic | YES | ~99140-G9000 (L), 99150-G9000 (R) (VERIFY VIA OUR DIAGNOSTIC SOFTWARE) | |
| Lane Keeping Assist (LKA) | Forward Camera | Camera | Static | YES | - | |
| Driver Attention Warning (DAW) | Forward Camera | Camera | Static | YES | - |
ADAS SYSTEM
YES Supported
Identification
- System type
- Module category
- Sensor location
Part Numbers
- OEM
- Alternative
Calibration & Triggers
- Calibration type
- Programming approach
- Requires PMI
- Trigger events
Technical Notes
- Chip / MCU
- Service notes
Need this calibrated?
Get a quote for ADAS calibration WHEN IS CALIBRATION REQUIRED?
Triggers for ADAS recalibration
Windshield Replacement Affected: FCA Forward Camera, Lane Keeping Assist, AEB, Driver Attention Warning
GDS2 ADAS static calibration required after windshield R&R. Level surface, calibration target at approx. 2.5m from vehicle front. Mobileye EyeQ3 camera sensitive to glass rake angle - use OEM-equivalent glass only. Verify all SmartSense DTCs clear before road test.
Front Bumper Repair or Replacement Affected: Front Radar (Smart Cruise, AEB), Front Ultrasonic Park Sensors
GDS2 radar alignment after front bumper work. Vehicle at curb weight on level surface. Inspect radar mounting bracket. Ultrasonic park sensor adaptation via GDS2 if sensors replaced.
Rear Bumper Repair or Replacement Affected: BSD Rear Radars (L/R), Rear Park Sensors
GDS2 BSD sensor initialization after rear bumper work. Functional test mandatory - confirm BCW and RCCA activate. Rear park sensor adaptation via GDS2 if sensors replaced.
Any Collision Affected: ACM (SRS), Forward Camera, Front Radar, BSD Radars, all deployed airbag components
Full GDS2 module scan mandatory. ACM crash clear or replacement depending on deployment severity. All ADAS sensors must be inspected for physical damage. Recalibrate all affected ADAS systems before delivery.
Any Module Replacement Affected: BCM, ECM, ACM, ABS, AVN, Cluster
GDS2 VIN coding and IMMO4 adaptation required for all security-relevant modules. Battery SOC must be adequate before programming. Confirm correct part suffix via Genesis EPC before ordering.
Forward Radar Replacement
Radar module replacement requires alignment/calibration using GDS Mobile.
BSM Sensor Replacement
Blind spot monitoring sensor replacement requires calibration using GDS Mobile.
Mirror Replacement
If BSD sensor is mirror-integrated, recalibration required. Verify sensor location; use GDS Mobile if applicable.
SRS Modules
SRS Control Module (SRSCM) 80100G9200NNB
- Part number
- 80100G9200NNB
- Location
- Under center console
- Manufacturer
- Continental
- Notes
- Requires GDS or compatible scan tool. SRSCM VIN write required. Clear DTCs after installation. Battery disconnect required.
SRS Control Module (SRSCM) 80310G9000
- Part number
- 80310G9000
- Location
- Under center console
- Manufacturer
- Continental
- Notes
- Requires GDS or compatible scan tool. SRSCM VIN write required. Clear DTCs after installation. Battery disconnect required.
SRS Control Module (SRSCM) 80200G9100
- Part number
- 80200G9100
- Location
- Under center console
- Manufacturer
- Continental
- Notes
- Requires GDS or compatible scan tool. SRSCM VIN write required. Clear DTCs after installation. Battery disconnect required.
ECU Modules
ECM - 2.0T Lambda II 4-cyl (252hp) ~39130-3LN (VERIFY VIA GDS2 VIN)
- Part number
- ~39130-3LN (VERIFY VIA GDS2 VIN)
- Protocol / method
- OBD Programming Port
- Coding required
- Yes
- Cloning supported
- Yes
- Chip / MCU
- Bosch MED17.9.8
- Notes
- GDS2 + Programming Port required. IMMO4 adaptation after ECM replacement. Verify engine code (G4KH) via VIN before ordering. Battery SOC must be >80% before programming session. Throttle body adaptation required after ECM replacement.
ECM - 3.3T Lambda II V6 Bi-Turbo (365hp) ~39130-3L (VERIFY VIA GDS2 VIN)
- Part number
- ~39130-3L (VERIFY VIA GDS2 VIN)
- Protocol / method
- OBD Programming Port
- Coding required
- Yes
- Cloning supported
- Yes
- Chip / MCU
- Bosch MED17.9.8
- Notes
- GDS2 + Programming Port. IMMO4 adaptation mandatory. Lambda II 3.3T (G6DP) - not interchangeable with 2.0T ECM.
BCM Modules
Body Control Module (BCM) ~95400-G9 (VERIFY VIA GDS2 VIN)
- Part number
- ~95400-G9 (VERIFY VIA GDS2 VIN)
- Security
- immo4
- Coding required
- Yes
- Cloning supported
- Yes
- Notes
- GDS2 required for VIN coding and immobilizer adaptation. IMMO4 security. Clone supported with compatible tool (Autel IM608 Pro, Launch Tech+). New BCM requires GDS2 coding session - central locking, windows, mirror fold, and immobilizer gateway all reside in BCM. Battery disconnect before removal.
TCU / TCM Transmission Modules
TCU - 8A45 8-Speed Auto 95440-G9
- Part number
- 95440-G9
- Protocol / method
- J2534
- Coding required
- Yes
- Cloning supported
- No
- Chip / MCU
- Hyundai HTCU
- Notes
- Requires dealer programming with GDS2. Adaptive relearn via test drive procedure. Use SP-IV ATF only.
ABS / Brake Modules
ABS/ESC Module (Mando / Continental) ~58920-G9300 (VERIFY VIA GDS2 VIN)
- Part number
- ~58920-G9300 (VERIFY VIA GDS2 VIN)
- Cloning supported
- Yes
- Notes
- GDS2 required for adaptation and air bleed after replacement. Automated bleed cycle available in GDS2 service function menu. Steering angle sensor recalibration required after ABS/ESC module replacement - GDS2 guided procedure. DTC C1604 common if bleed incomplete.
Other Modules (IPC, SAS)
Instrument Panel Cluster (IPC) 94003-G9000
- Part number
- 94003-G9000
- Cloning supported
- Yes
- Notes
- IPC cloning required for mileage preservation during replacement. Use Launch advanced programming tool or EEPROM programming tool for EEPROM read/write.
Instrument Panel Cluster (IPC) 94003-G9010
- Part number
- 94003-G9010
- Cloning supported
- Yes
- Notes
- IPC cloning required for mileage preservation during replacement. Use Launch advanced programming tool or EEPROM programming tool for EEPROM read/write.
Steering Angle Sensor (SAS)
- Coding required
- Yes
- Notes
- INTEGRATED (clock spring / steering column module
Steering Angle Sensor (SAS)
- Coding required
- Yes
- Notes
- cross-year extension)
Connectivity & Accessories
Digital Instrument Cluster ~94013-G9 (VERIFY VIA GDS2)
- Part number
- ~94013-G9 (VERIFY VIA GDS2)
- Notes
- GDS2 VIN coding required.
Around View Monitor (AVM) Camera System ~95760-G9 (VERIFY VIA GDS2)
- Part number
- ~95760-G9 (VERIFY VIA GDS2)
- Notes
- 4-camera surround view system on Sport and Elite trims. GDS2 AVM calibration required after any camera replacement or bumper/mirror repair affecting camera position. Static calibration mat required per WSM.
ARCHITECTURE & CONNECTIVITY
Architecture & Connectivity
- Body Construction
- Steel unibody; high-strength steel front/rear subframes
- OBD Protocol
- ISO 15765-4 CAN (500 kbps); UDS (ISO 14229)
- CAN Architecture
- Hyundai/Genesis CAN bus (HS-CAN, MS-CAN, LIN for body subsystems)
- Infotainment
- Genesis Connected Services AVN; 8-inch display; Apple CarPlay / Android Auto
- OTA Capable
- No
- Infotainment Name
- Genesis Connected Services
- ECU/TCM Unlocking
- Contact us
- ECU/TCM Flashing
- Contact us
FREQUENTLY ASKED QUESTIONS
FAQ
How much does ADAS calibration cost for a 2019 Genesis G70?
ADAS calibration pricing for a 2019 Genesis G70 depends on which of its 5 documented systems need work after a repair. This vehicle is documented with Forward Collision-Avoidance Assist (FCA) - Front Camera, Forward Radar (77GHz), Blind Spot Detection (BSD) - Rear Radar, Lane Keeping Assist (LKA), and Driver Attention Warning (DAW). We provide a fixed quote after confirming the operations performed - send the VIN, the repair scope (windshield R&R, bumper work, alignment, collision), and any DTCs so the quote response can include a real number.
Can you reset the airbag light on a 2019 Genesis G70?
Yes. The 2019 Genesis G70 uses a factory SRS control module that we support. We read and clear stored crash data, then restore the module to factory status so the airbag warning light goes out and the system returns to full operation. Reference part number on this vehicle: 80100G9200NNB. Mobile diagnosis and programming are available in DFW, and mail-in module service is available nationwide. Send the part number and a description of what triggered the light, and we will provide a quote and scheduling window.
What is needed after replacing the windshield on a 2019 Genesis G70?
After windshield replacement on a 2019 Genesis G70, Forward Collision-Avoidance Assist (FCA) - Front Camera, Forward Radar (77GHz), and Lane Keeping Assist (LKA) rely on the forward-facing camera and require recalibration before the systems return to operation. We perform the calibration on-site in the DFW Metroplex with OE target fixtures. Mail-in module service is available nationwide for eligible module work.
How long does a 2019 Genesis G70 module service take?
Most 2019 Genesis G70 onsite jobs are typically scheduled within 24-48 hours once vehicle readiness, access, and route timing are confirmed. This vehicle has roughly 13 programmable modules documented in our database (2 ECU, 1 BCM, 1 TCU, 1 ABS, plus IPC/SAS/gateway/accessory). Mobile module work and ADAS calibration are scheduled in the DFW service area after quote review. Mail-in module service is available nationwide.
Do you cover the 2019 Genesis G70 on-site, or is this mail-in only?
We run a mobile unit across the DFW Metroplex for on-vehicle work (ADAS calibration, post-repair recoding, and supported module work). Mail-in module service is available nationwide. Quote the work and we will confirm the active service path for the 2019 Genesis G70. Do not ship a module unless support confirms next steps.
What kind of warranty do you offer on 2019 Genesis G70 programming?
Every programming, cloning, and calibration job on the 2019 Genesis G70 is backed by a workmanship warranty covering the scope of work we performed: 1-year unlimited on all flashes, clones, and ADAS calibrations. If a module we programmed or a calibration we performed fails to function as expected, return it and we restore it at no charge. The warranty covers our work; it does not cover unrelated mechanical or electrical failure of the module itself.
Which modules on a 2019 Genesis G70 can you actually service?
We program, clone, repair, or replace the full programmable-module stack on a 2019 Genesis G70. For this vehicle our database documents:
- 2 engine control (ECU/PCM)
- 1 transmission control (TCU/TCM)
- 1 body control (BCM and related)
- 1 ABS / brake control (EBCM)
- 1 immobilizer / security
- 1 key & fob
- 2 instrument cluster (IPC)
- 2 steering angle sensor (SAS)
- 5 ADAS module
Infotainment on this platform: Genesis Connected Services. Send the VIN and the operations performed and we will confirm support and pricing.
Additional Module Part Numbers
Additional OEM-sourced part numbers for the 2019 Genesis G70 covering ADAS, ECU/PCM, BCM, TCU/TCM, SRS, ABS/EBCM, instrument cluster (IPC), gateway, and steering angle sensor modules when available. These reference numbers assist technicians with module identification and sourcing prior to programming.
- ADAS Module Part Numbers
- 99110-G9000, 96400-G9000
- ECU / PCM Part Numbers
- 39110-3LTA0, 39110-3LTB0
- BCM / Body Module Part Numbers
- ~95400-G9 (VERIFY VIA GDS2 VIN)
- TCU / TCM Part Numbers
- 95440-G9
- SRS / Airbag Module Part Numbers
- 80100G9200NNB, 80310G9000, 80200G9100
- ABS / EBCM Part Numbers
- 58920-G9300, 58920-G9350
- Instrument Cluster (IPC) Part Numbers
- 94003-G9000, 94003-G9010
- Transmission Control Module (TCM) Part Numbers
- 95440-G9
Part numbers are OEM base references. Verify exact suffix via VIN-specific build data before ordering. Core Auto Logic provides mobile programming services for all listed modules in the DFW area.
Different trim or build?
Send your VIN and we'll confirm exact module support and pricing in the quote response.
Hit a security wall? We've got the keys.
1-year unlimited warranty on every flash and calibration.
Shared module fitment
Vehicles sharing modules with the 2019 Genesis G70
These vehicles use one or more of the same replacement modules indexed for this vehicle.
Finish the repair
Need help finishing this repair?
Get onsite help in Dallas-Fort Worth. Ask about same-day availability or a one-time remote session for eligible non-VSP work.
Factory programming software Explore one-time factory coding and programming. We confirm the software and procedure for your vehicle. Module programming & recovery Replacing a module or dealing with a failed programming attempt? Send the part numbers and fault scan for review. Onsite tools & equipment Bring in a technician or ask about hourly, daily and weekly rentals where licensing and equipment availability allow.