Skip to main content
Mobile Module Service

ABS / EBCM Programming, Cloning & Repair

DFW Mobile programming for shops, rebuilders and independent mechanics.

Mobile service is available in the Dallas / Fort Worth service area; mail-in module service is available nationwide. Our work carries a 1-year unlimited-mile workmanship warranty.

Get a Quote Call a Tech

Mobile in DFW - mail-in available nationwide. Most quotes are returned in under 4 business hours.

ABS / EBCM Programming, Cloning & Repair
BENCH / OEM PROGRAM
Flat-rate pricing - confirmed before any work begins
Quotes are free - no obligation.
Quotes returned in under 4 business hours
Start a Quote

Why Brake Shops and Chassis Builders Choose Core Auto Logic

Modern ABS / EBCM modules are tied into stability control, traction and ADAS. A swap or repair without programming sets the brake light, kills traction control and can disable AEB. We do the full programming + bleed + adaptation sequence.

Request a Quote
OEM Software for ABS Programming
Genuine factory tools cover GM EBCM, Ford ABS, Stellantis MK series, Toyota Skid Control ECU, Honda VSA and most European platforms. The right calibration for the build, every time.
OEM
Bench Repair on Common Failures
ABS modules with internal valve-driver or solenoid faults can often be bench-repaired and re-programmed instead of replaced. Saves weeks of dealer parts wait on legacy platforms.
BENCH
Bleed + Adaptation Included
Every ABS programming job ends with the OEM-mandated automated bleed routine, steering-angle relearn and stability-control adaptation - so the brake pedal feels right when the truck rolls out.
ADAPT
Mail-In ABS and EBCM Service
Mail-in ABS and EBCM service is available nationwide. Submit the VIN, fault codes, part number, and job details for review before shipping.
Mail-in available Request review VIN and DTC review Quote required
MAIL-IN AVAILABLE - REQUEST REVIEW
REQUEST REVIEW

Two Ways to Get Your ABS / EBCM Programming, Cloning & Repair Done

Request nationwide mail-in bench service, or book a mobile visit if you're in the DFW metro. Our workmanship warranty covers defects in our completed work.

We Come to Your Shop

We bring OEM software and programming equipment to your DFW location. Any required vehicle checks or road procedures are confirmed with you.

  1. Schedule a visitWe confirm availability and an appointment window after reviewing the request
  2. Tech arrives on-siteRoute window confirmed before arrival, full tool kit in the van
  3. Service in-vehicleComplete the agreed programming, coding or module work using the applicable procedure
  4. Required verificationVehicle checks, adaptations or road procedures depend on the service and are confirmed in the agreed scope
COVERAGE
DFW Metroplex
Dallas, Fort Worth, Plano, Arlington, Frisco, Irving
Request Onsite Service

Mail-In Module Service

Submit the request for review. If accepted, Core Auto Logic sends the final quote and packing and shipping instructions.

  1. Submit for reviewStart with vehicle details and the requested work. VIN, part numbers and label photos are helpful if available; VIN is optional initially
  2. Wait for acceptanceDo not ship before receiving the final quote and instructions
  3. Ship inboundThe customer pays and arranges inbound shipping
  4. Tracked returnReturn shipping is included in the final quote
MAIL-IN ADDRESS
CORE AUTO LOGIC
6805 MAIN ST STE 430 PMB 1015
THE COLONY TX 75056
Start Mail-In Request

What to know before requesting service

Start with year, make, model and a short description. VIN is optional for an initial request; we may request it later to confirm compatibility.

  • Is this the right service?We review controller faults and replacement compatibility. Hydraulic, sensor and wiring faults may require separate work.
  • Helpful detailsVehicle details, symptoms and module-label photos if available.
  • What happens afterwardBleeding, coding or calibrations may require the vehicle and the applicable factory procedure.
  • Price and timingThe quote identifies the accepted module work and any additional setup.

DFW onsite or nationwide mail-in for eligible module work. The accepted quote confirms the delivery path. Appointment and completion timing are confirmed after review; do not ship before acceptance. See our factory software directory and service terms.

A quote request does not confirm an appointment. We will confirm scope, price, and availability with you.

What happens next

From your request to completed work and documentation.

  1. Submit Your Quote RequestProvide the VIN, a brief description of the fault codes or symptoms, and whether you need mobile service in DFW or mail-in service nationwide. Quote returned within 4 business hours.
    Submit Your Quote Request - Core Auto Logic abs-module-repair step 1
  2. Module IntakeFor mobile service, we come to your location with OEM software and work at the vehicle. For mail-in service, submit the EBCM request for review and wait for the accepted quote and instructions before shipping. Mail-in address: CORE AUTO LOGIC, 6805 MAIN ST STE 430 PMB 1015, THE COLONY TX 75056.
    Module Intake - Core Auto Logic abs-module-repair step 2
  3. Programming or RepairWe VIN-pair, configure variant options, flash to the latest OEM calibration, and run a bench CAN simulation test. Water-damaged modules go through component-level repair before programming.
    Programming or Repair - Core Auto Logic abs-module-repair step 3
  4. Return & DocumentationFor approved DFW mobile work, the programming report records the VIN, calibration level, and post-program DTC confirmation before the final road test.
    Return & Documentation - Core Auto Logic abs-module-repair step 4

Frequently Asked Questions

Controller repair concerns the electronic module within the accepted scope. It does not automatically repair the hydraulic pump, valves, wheel-speed sensors, wiring or other brake components. Diagnosis must identify the fault before deciding whether to repair the controller, program a replacement or address another component.
Some vehicles support used ABS controllers, while others have compatibility or security restrictions. Provide the vehicle details and original and replacement part numbers before purchasing. We confirm whether the proposed module can be configured for your vehicle and which vehicle procedures are required.
Mail-in EBCM service is available nationwide after review. Do not remove or ship the controller until Core Auto Logic accepts the request and sends the final quote and instructions. For approved DFW mobile service, no removal is needed - we program in place through the diagnostic port. Mail-in address: CORE AUTO LOGIC, 6805 MAIN ST STE 430 PMB 1015, THE COLONY TX 75056.
We can review the fault codes, replacement part number and work already performed. Configuration or calibration may be incomplete, but sensor, wiring, power supply or hydraulic faults can also keep the warning on. The diagnostic results determine whether programming is appropriate and whether other repairs are needed.
Repairability depends on the extent and location of the damage. Corrosion, damaged circuitry and unavailable components can make replacement necessary. Send clear photos and fault details for initial review; a final repair decision may require inspection. A repair estimate does not guarantee that every water-damaged controller can be recovered.
The OEM replacement procedure determines the required setup. Depending on the vehicle and work performed, this can include configuration, steering-angle or motion-sensor calibration, an automated bleed and vehicle checks. Bench service does not complete procedures that require the installed vehicle. The accepted scope identifies the remaining installation work.

Everything covered in this service

The agreed work is verified and documented before the job is completed.

VIN Pairing & Variant Config
VIN
Replacement modules require VIN write, vehicle configuration, and traction/stability control option-byte setup via OEM-level diagnostic software before full brake system function is restored.
Bench Repair for Water-Damaged Units
BENCH
Failed ABS control boards damaged by water or voltage spikes can often be repaired at the component level and reprogrammed - a significant cost saving over a new HCU assembly.
Module Cloning
CLONE
We clone the EEPROM data from a failed EBCM to a donor unit, preserving VIN linkage, calibration adaptation, and sensor zero-point offsets where the platform supports it.
Mail-In EBCM Service
MAIL
Mail-in EBCM service is available nationwide after request review. If accepted, Core Auto Logic sends the final quote and packing and shipping instructions before you ship. Mail-in address: CORE AUTO LOGIC, 6805 MAIN ST STE 430 PMB 1015, THE COLONY TX 75056.
Full DTC Scan Before & After
DTC
Every job includes a pre-work fault scan and a post-programming clear/confirmation scan so you have documentation that the ABS system left our bench clean.
1-Year Workmanship Warranty
GUARANTEE
Programming and repair work is backed by our standard 1-year unlimited-mile workmanship warranty. We correct defects in our completed programming work under that warranty; unrelated vehicle faults are excluded.

Common reasons customers book this service

Tap a card to see what triggers this service and which systems are affected.

A lit ABS or stability control warning with a C-code fault stored in the ABS module often indicates the module needs programming, calibration data update, or replacement and relearn rather than a full wheel-speed sensor swap.
Water ingress into the EBCM connector or HCU electronics is common after deep water crossing or pressure washing. A failed module can be bench-repaired and reprogrammed rather than replaced at full dealer cost.
New, remanufactured, and used ABS modules require VIN-pairing and variant configuration before stability control and ABS return to normal operation. A generic scan tool cannot perform this initialization.
If ABS engages at speeds or conditions where it should not, the fault may be in the EBCM calibration data rather than the hardware. Reflashing the module to the latest OEM calibration often resolves this without replacing the HCU.
Following brake service on vehicles with integrated electronic brake control, the module may require an automated bleed cycle and pressure sensor reset via factory software before normal pedal feel returns.
Tools and technical coveragePlatform access, equipment, and procedure details
TOOL CAPABILITY MATRIX

Capable platforms for this work

Platforms used for brake control diagnostics, coding, initialization, zero-point relearns, and factory programming.

ABS and stability-control coding
AFTERMARKET PLATFORM
Autel, Launch Tech, Topdon Used for supported brake-module configuration, active tests, and relearns.
Coverage varies by vehicle Security gateway access required
Source basis: Autel, Launch Tech, and Topdon scanner-vendor capability documentation.
Factory initialization and flash programming
OEM SOFTWARE
FDRS / GDS2 / Techstream / wiTECH 2.0 / ODIS Required when the manufacturer locks the module setup or flash routine to the OEM portal.
No practical workaround
Source basis: OEM brake-control programming and guided service software.

ABS / EBCM Failure Indicators

Symptoms that point to an ABS module that needs programming, repair or replacement. If the mechanical brake work checks out and these still appear, the module is the problem.

ABS Light On Constant
C-codes (C0035, C0040, C1234) that will not clear after a known-good wheel-speed sensor or brake repair point to an internal module fault.
No Communication With ABS
U0121 "Lost Communication With ABS Module" with no response on bidirectional commands. Module is dead, bricked, or has a power/ground fault.
Traction Control Disabled
TCS / VSC / StabiliTrak fault on cluster, can be paired with ABS code. Module needs programming or replacement plus stability-control re-learn.
Brake Pedal Pulse / Hard Pedal
After service, pedal pulses on smooth roads or feels hard at startup. Adaptation data lost; module needs the OEM bleed and zero-point routine.

Built around what your shop actually needs.

About this service.

Workmanship warranty

A 1-year unlimited-mile workmanship warranty on our work.

If a defect in our calibration or programming work appears, contact us so we can put it right at no charge. We confirm coverage for your specific job before work begins.

1-Year Unlimited Miles
Coverage for our completed service
Clear Scope and Pricing
Approve the scope and charges before work begins
Workmanship support
Contact us about a defect in our work
Direct Tech Line
Talk with our service team

Ready to get this programmed and out the door?

Mobile service is available in DFW, and mail-in module service is available nationwide. Submit a mail-in request for review. Most quotes are returned in under 4 business hours.

Request DFW Mobile Service Start Mail-In Request

Prefer to talk it through? (945) 382-4065 - Monday-Saturday, 9 AM-7 PM Central. Closed Sunday.