Electronic systems coverage
This 2005 GMC Canyon page does not list sensor-system records yet; module, security, and programming support is confirmed by VIN before service.
View systems 3,200+ Vehicles Supported
1-Year Unlimited Guarantee
DFW Mobile Service
DFW Serving Dallas / Fort Worth
No ADAS systems detected on this vehicle. Want to switch to Onsite Diagnostics? Most non-ADAS issues are diagnosed and resolved in a single visit.
2005 GMC Canyon Supported Services
2005 GMC Canyon
ADAS calibration, module programming, and security relearns
Full ADAS calibration, module programming, and key security work for the 2005 GMC Canyon. Mobile service is available in the Dallas/Fort Worth service area; mail-in is temporarily unavailable.
Technical snapshot
- Platform GMT355 (1st Gen, 2004-2012)
- CAN Architecture HS-CAN (500 kbps) - ISO 15765-4 compliant; OBD2 DLC Pin 6/14
- Security GM PASSKey III / PassLock II (BCM security seed); resistor pellet or PassLock cylinder sensor; PIN via Tech 2 or GDS2; AKL requires BCM relearn procedure + security PIN
OVERVIEW
Expert ADAS calibration, module programming, and diagnostic recovery for the 2005 GMC Canyon. On this vehicle we cover documented systems include No Factory ADAS Systems, this GMT355 (1st Gen, 2004-2012) platform vehicle, PK3/PK3+ / PEPS immobilizer support. Mobile across the DFW Metroplex; mail-in module work is temporarily unavailable.
Platform
GMT355 (1st Gen, 2004-2012)
Production
2004-present
Trim Levels
-
Drivetrain
RWD / 4WD
Engine
-
CAN Speed
HS-CAN (500 kbps) - ISO 15765-4 compliant; OBD2 DLC Pin 6/14
Exact-year service summary for 2005 GMC Canyon
Programmable modules
This page indexes 23 programmable module records across SRS, ECU, BCM, TCU/TCM, ABS, and SAS coverage.
View modulesGateway and security
This page includes 9 gateway, immobilizer, or key-security records for this 2005 GMC Canyon.
View securityCore Auto Logic capability
Core Auto Logic supports exact-year diagnostics, module programming, and security-access planning for the 2005 GMC Canyon using the documented module data on this page.
Choose a sectionWhat changes on this exact year
Feature availability
Immobilizer: PK3/PK3+ / PEPS - Standard; Platform: GMT355 (1st Gen, 2004-2012) - Confirmed
Driver-assist suite
No standard ADAS suite - pre-Safety Assist generation. Optional Forward Collision Alert and Lane Departure Warning on upper trims.
Infotainment context
GMC MyLink - 7 inch
Network and access
CAN: HS-CAN (500 kbps) - ISO 15765-4 compliant; OBD2 DLC Pin 6/14
Tool access for this exact year
Representative tool access paths for this exact model year, gated by the vehicle data and source packet we currently trust.
Factory scan, coding, and calibration access
GM GDS2 / GM Tech2Win / GM MDI 2
Factory routines and secure server authorization control this path when aftermarket coverage is not enough for the VIN.
OEM subscription required
Make-level OEM tool map plus exact-year gateway and ADAS fields.
ADAS scan, setup, and verification
Autel, Launch Tech, Topdon
Used where aftermarket coverage supports the procedure; OEM software remains required for locked factory routines.
Tool subscription required
Service-level scanner-vendor source packet plus exact-year ADAS records.
Bench cloning and chip-level recovery
Alientech / Autotuner / Orange5 / Scanmatik / Flex / VVDI2 / PCMFlash / CGDI / X-Prog
Used only when the module, donor data, EEPROM, MCU, or crash-data workflow requires bench or chip-level handling.
Bench/chip-level only
Bench programmer source packet plus exact-year module/security records.
Choose a section to view data
SUPPORTED SYSTEMS
What we service on this vehicle
Documented module coverage for the 2005 GMC Canyon. Counts reflect modules our techs have programmed or calibrated on this exact platform.
Engine / ECU Programming
2 modules documented
Powertrain reprogramming, calibration updates, replacement ECU configuration and security access.
Open Modules tabBCM / Body Programming
1 module documented
Body control module, gateway and accessory programming. Includes feature-bit reconfiguration.
Open Modules tabGateway / Security Access
6 modules documented
Secure gateway module identification, bypass workflow and security-access planning before programming.
Open Security tabTCU / Transmission
2 modules documented
Transmission control module reprogramming, adaptive learning reset and replacement TCM clone.
Open Modules tabSRS / Airbag Reset
11 modules documented
Crash-data clear, hard-code reset and replacement airbag module configuration.
Open Modules tabABS / Brake Module
3 modules documented
ABS / EBCM bleed support, replacement module coding and yaw-rate sensor calibration.
Open Modules tabKey Security & Immobilizer
1 module documented
Immobilizer modules, key/fob types, add-key + all-keys-lost (AKL) capability and security overview.
Open Security tabIPC, SAS & Other Modules
2 modules documented
Instrument cluster cloning, steering angle sensor calibration and other supporting modules.
Open Modules tabConnectivity & Accessories
2 modules documented
Infotainment radio, surround view, remote start, trailer brake controller and other equipped systems.
Open Modules tabNeed something not listed? Most undocumented modules can still be programmed.
Feature availability 2
Immobilizer: PK3/PK3+ / PEPS
StandardKey programming requires manufacturer-level tool access. Add key supported. All keys lost (AKL) supported.
Platform: GMT355 (1st Gen, 2004-2012)
ConfirmedVerify platform code matches when cross-referencing part numbers across model years.
WHAT WE RESOLVE
Common issues on this vehicle
Common GMC Canyon issues we resolve on this platform: No Factory ADAS Systems recalibration after windshield/bumper/suspension/CCM service. Module programming for replacement ECU/PCM, BCM, TCU, or accessory modules - GMT355 (1st Gen, 2004-2012) platform uses HS-CAN (500 kbps) - ISO 15765-4 compliant; OBD2 DLC Pin 6/14. Key programming and immobilizer faults - PK3/PK3+ / PEPS immobilizer; all-keys-lost supported.
ADAS CALIBRATION MATRIX
ADAS systems on this vehicle
No standard ADAS suite - pre-Safety Assist generation. Optional Forward Collision Alert and Lane Departure Warning on upper trims.
Scroll for part numbers and Details
| System | Type | Category | Cal. Type | Supported | Part # | Actions |
|---|---|---|---|---|---|---|
| No Factory ADAS Systems | None | None | None | No | - |
ADAS SYSTEM
YES Supported
Identification
- System type
- Module category
- Sensor location
Part Numbers
- OEM
- Alternative
Calibration & Triggers
- Calibration type
- Programming approach
- Requires PMI
- Trigger events
Technical Notes
- Chip / MCU
- Service notes
Need this calibrated?
WHEN IS CALIBRATION REQUIRED?
Triggers for ADAS recalibration
PCM Replacement
GDS2 SPS calibration download + PASSLOCK relearn.
EBCM Replacement
GDS2 ABS automated bleed + WSS relearn.
SRS MODULES
SRS Modules
Sensing & Diagnostic Module (SDM) x11
15239331 Under center console
- PART
- 15239331
- LOCATION
- Under center console
- MFG
- Continental
- NOTES
- Requires GM GDS2 / Tech2 or J2534 for SRS reset. DTC B0100 common after crash events. Wait 90 seconds after ignition off before disconnecting battery.
15239332 Under center console
- PART
- 15239332
- LOCATION
- Under center console
- MFG
- Continental
- NOTES
- Requires GM GDS2 / Tech2 or J2534 for SRS reset. DTC B0100 common after crash events. Wait 90 seconds after ignition off before disconnecting battery.
12249529 Under center console
- PART
- 12249529
- LOCATION
- Under center console
- MFG
- Continental
- NOTES
- Requires GM GDS2 / Tech2 or J2534 for SRS reset. DTC B0100 common after crash events. Wait 90 seconds after ignition off before disconnecting battery.
12249539 Under center console
- PART
- 12249539
- LOCATION
- Under center console
- MFG
- Continental
- NOTES
- Requires GM GDS2 / Tech2 or J2534 for SRS reset. DTC B0100 common after crash events. Wait 90 seconds after ignition off before disconnecting battery.
12249549 Under center console
- PART
- 12249549
- LOCATION
- Under center console
- MFG
- Continental
- NOTES
- Requires GM GDS2 / Tech2 or J2534 for SRS reset. DTC B0100 common after crash events. Wait 90 seconds after ignition off before disconnecting battery.
12249559 Under center console
- PART
- 12249559
- LOCATION
- Under center console
- MFG
- Continental
- NOTES
- Requires GM GDS2 / Tech2 or J2534 for SRS reset. DTC B0100 common after crash events. Wait 90 seconds after ignition off before disconnecting battery.
15779005 Under center console
- PART
- 15779005
- LOCATION
- Under center console
- MFG
- Continental
- NOTES
- Requires GM GDS2 / Tech2 or J2534 for SRS reset. DTC B0100 common after crash events. Wait 90 seconds after ignition off before disconnecting battery.
10368336 Under center console
- PART
- 10368336
- LOCATION
- Under center console
- MFG
- Continental
- NOTES
- Requires GM GDS2 / Tech2 or J2534 for SRS reset. DTC B0100 common after crash events. Wait 90 seconds after ignition off before disconnecting battery.
10368760 Under center console
- PART
- 10368760
- LOCATION
- Under center console
- MFG
- Continental
- NOTES
- Requires GM GDS2 / Tech2 or J2534 for SRS reset. DTC B0100 common after crash events. Wait 90 seconds after ignition off before disconnecting battery.
20864450 Under center console
- PART
- 20864450
- LOCATION
- Under center console
- MFG
- Continental
- NOTES
- Requires GM GDS2 / Tech2 or J2534 for SRS reset. DTC B0100 common after crash events. Wait 90 seconds after ignition off before disconnecting battery.
25980812 Under center console
- PART
- 25980812
- LOCATION
- Under center console
- MFG
- Continental
- NOTES
- Requires GM GDS2 / Tech2 or J2534 for SRS reset. DTC B0100 common after crash events. Wait 90 seconds after ignition off before disconnecting battery.
ECU MODULES
ECU Modules
Engine Control Module (ECM) - 2.8L LK5 I4 19209821
- PART
- 19209821
- PROTOCOL
- J2534
- CODING
- Yes
- CLONE
- No
- NOTES
- Same service assembly 19209821 as 2004 for 2.8L. Additional calibrations: 12591648, 12604438. Sibling: 2005 Chevrolet Colorado 2.8L.
Engine Control Module (ECM) - 3.5L LK5 I5 19209821
- PART
- 19209821
- PROTOCOL
- J2534
- CODING
- Yes
- CLONE
- No
- NOTES
- Same service assembly 19209821 for 2005 Canyon 3.5L I5.
BCM MODULES
BCM Modules
BCM (Body Control Module)
- NOTES
- GM BCM. GDS2/MDI2 SPS programming + PASSLOCK/PASSKEY relearn.
TCU / TCM TRANSMISSION MODULES
TCU / TCM Transmission Modules
TCU - 4L60E 4-Speed Auto 24227223
- PART
- 24227223
- PROTOCOL
- J2534
- CODING
- Yes
- CLONE
- No
- CHIP/MCU
- Motorola MPC555
- NOTES
- Requires GM Tech2 or MDI for programming. VIN and calibration must match. Relearn procedure via drive cycle required. Use DEXRON VI ATF.
TCU - 5L40E 5-Speed Auto 24227226
- PART
- 24227226
- PROTOCOL
- J2534
- CODING
- Yes
- CLONE
- No
- CHIP/MCU
- Motorola MPC555
- NOTES
- Requires GM Tech2 or MDI for programming. VIN and calibration must match. Adaptive learning reset required after installation. Use DEXRON VI ATF.
ABS / BRAKE MODULES
ABS / Brake Modules
EBCM (Electronic Brake Control Module)
- NOTES
- GM EBCM. GDS2 automated bleed procedure + WSS relearn.
Wheel Speed Sensor - Front (each)
- NOTES
- Replace if DTC C0035/C0040 set.
Wheel Speed Sensor - Rear (each)
- NOTES
- Replace if DTC C0045/C0050 set.
OTHER MODULES (IPC, SAS)
Other Modules (IPC, SAS)
Steering Angle Sensor (SAS)
- CODING
- Yes
- NOTES
- INTEGRATED (clock spring / steering column module
Steering Angle Sensor (SAS)
- CODING
- Yes
- NOTES
- cross-year extension)
CONNECTIVITY & ACCESSORIES
Connectivity & Accessories
ICS - GMC Infotainment System (11.3 inch) 84926700
- PART
- 84926700
- NOTES
- SPS2 PMI. Google built-in. Wireless CarPlay/Android Auto. ProGrade Trailering display integration.
Driver Information Center (DIC) 84926710
- PART
- 84926710
- NOTES
- SPS2 PMI. Mileage in BCM.
GATEWAY / SECURITY MODULES
Gateway / Security Modules
Central Gateway Module
- SECURITY
- VIN-locked (UDS)
- VIN LOCKED
- Yes
- CODING
- Yes
- CHIP/MCU
- D70F3558(read-write)
- NOTES
- Compatibility label: Buick. Central gateway routes CAN/CAN-FD/Ethernet between module domains. Replacement requires VIN write and as-built configuration load via OEM software (ODIS, FDRS, DTS Monaco, etc.).
Central Gateway Module
- SECURITY
- VIN-locked (UDS)
- VIN LOCKED
- Yes
- CODING
- Yes
- CHIP/MCU
- 2015- 1M12S
- NOTES
- Compatibility label: CRUZE. Central gateway routes CAN/CAN-FD/Ethernet between module domains. Replacement requires VIN write and as-built configuration load via OEM software (ODIS, FDRS, DTS Monaco, etc.).
Central Gateway Module
- SECURITY
- VIN-locked (UDS)
- VIN LOCKED
- Yes
- CODING
- Yes
- CHIP/MCU
- 2015- 1M12S
- NOTES
- Compatibility label: Cavalier. Central gateway routes CAN/CAN-FD/Ethernet between module domains. Replacement requires VIN write and as-built configuration load via OEM software (ODIS, FDRS, DTS Monaco, etc.).
Central Gateway Module
- SECURITY
- VIN-locked (UDS)
- VIN LOCKED
- Yes
- CODING
- Yes
- CHIP/MCU
- D70F3385(read-write)
- NOTES
- Compatibility label: Chevrolet. Central gateway routes CAN/CAN-FD/Ethernet between module domains. Replacement requires VIN write and as-built configuration load via OEM software (ODIS, FDRS, DTS Monaco, etc.).
Central Gateway Module
- SECURITY
- VIN-locked (UDS)
- VIN LOCKED
- Yes
- CODING
- Yes
- CHIP/MCU
- 2015- 1M12S
- NOTES
- Compatibility label: Excelle. Central gateway routes CAN/CAN-FD/Ethernet between module domains. Replacement requires VIN write and as-built configuration load via OEM software (ODIS, FDRS, DTS Monaco, etc.).
Central Gateway Module
- SECURITY
- VIN-locked (UDS)
- VIN LOCKED
- Yes
- CODING
- Yes
- CHIP/MCU
- 2015- 1M12S
- NOTES
- Compatibility label: SAIL. Central gateway routes CAN/CAN-FD/Ethernet between module domains. Replacement requires VIN write and as-built configuration load via OEM software (ODIS, FDRS, DTS Monaco, etc.).
KEY SECURITY & IMMOBILIZER
Key Security & Immobilizer
- System PK3/PK3+ / PEPS
- Add Key Yes
- All Keys Lost Yes
GM PASSKey III / PassLock II (BCM security seed); resistor pellet or PassLock cylinder sensor; PIN via Tech 2 or GDS2; AKL requires BCM relearn procedure + security PIN
IMMOBILIZER MODULES
Immobilizer Modules
BCM (PASS-Key III+ database)
- NOTES
- GM PASSKEY III+ in BCM. GDS2 password reset for AKL. Seed/key algorithm via GDS2 IMMO function.
KEY & FOB TYPES
Key & Fob Types
GM PASSKEY III+ Transponder Key
- NOTES
- Resistor + transponder. GDS2 or Tech 2 programming. AKL via security seed.
GM Remote Key Fob (RKE)
- NOTES
- 315MHz. Program via GDS2 or 10x lock/unlock cycle for basic fobs.
Replacement Notes
PK3/PK3+ / PEPS system. SPS/ACDelco TDS required for key programming and module replacement. Security pin required; akl supported.
ARCHITECTURE & CONNECTIVITY
Architecture & Connectivity
- Body Construction
- Body-on-frame - high-strength steel
- OBD Protocol
- ISO 9141-2 / KWP2000 (OBD-II, pre-CAN)
- CAN Architecture
- HS-CAN (500 kbps) - ISO 15765-4 compliant; OBD2 DLC Pin 6/14
- Infotainment
- GMC MyLink - 7 inch
- OTA Capable
- No
- ECU/TCM Unlocking
- Contact us
- ECU/TCM Flashing
- Confirmed
Reviewed coverage: 2005 - 2.8L Vortec 16v (LK5), 2.9L Vortec 16v (LLV).
Confirm the exact engine, ECU, and any prerequisite access method before service.
FREQUENTLY ASKED QUESTIONS
FAQ
How much does ADAS calibration cost for a 2005 GMC Canyon?
ADAS calibration pricing for a 2005 GMC Canyon depends on which of its 1 documented systems need work after a repair. This vehicle is documented with No Factory ADAS Systems. We provide a fixed quote after confirming the operations performed - send the VIN, the repair scope (windshield R&R, bumper work, alignment, collision), and any DTCs so the quote response can include a real number.
Can you reset the airbag light on a 2005 GMC Canyon?
Yes. The 2005 GMC Canyon uses a factory SRS control module that we support. We read and clear stored crash data, then restore the module to factory status so the airbag warning light goes out and the system returns to full operation. Reference part number on this vehicle: 15239331. Mobile diagnosis and programming are the active service path. Mail-in bench intake is temporarily unavailable. Send the part number and a description of what triggered the light, and we will provide a quote and scheduling window.
What is needed after replacing the windshield on a 2005 GMC Canyon?
After windshield replacement on a 2005 GMC Canyon, the forward-facing ADAS camera typically requires recalibration before lane-keep, pre-collision, and adaptive-cruise systems return to operation. We perform the calibration on-site in the DFW Metroplex with OE target fixtures. Mail-in intake is temporarily unavailable.
How long does a 2005 GMC Canyon module service take?
Most 2005 GMC Canyon onsite jobs are typically scheduled within 24-48 hours once vehicle readiness, access, and route timing are confirmed. This vehicle has roughly 19 programmable modules documented in our database (2 ECU, 1 BCM, 2 TCU, 3 ABS, plus IPC/SAS/gateway/accessory). Mobile module work and ADAS calibration are scheduled in the DFW service area after quote review. Mail-in module intake is temporarily unavailable.
Do you cover the 2005 GMC Canyon on-site, or is this mail-in only?
We run a mobile unit across the DFW Metroplex for on-vehicle work (ADAS calibration, key programming, IMMO pairing, post-repair recoding, and supported module work). Mail-in module intake is temporarily unavailable. Quote the work and we will confirm the active service path for the 2005 GMC Canyon. Do not ship a module unless support confirms next steps.
What kind of warranty do you offer on 2005 GMC Canyon programming?
Every programming, cloning, and calibration job on the 2005 GMC Canyon is backed by a workmanship warranty covering the scope of work we performed: 1-year unlimited on all flashes, clones, and ADAS calibrations. If a module we programmed or a calibration we performed fails to function as expected, return it and we restore it at no charge. The warranty covers our work; it does not cover unrelated mechanical or electrical failure of the module itself.
Can you program a 2005 GMC Canyon with no working keys (all-keys-lost)?
Yes - all-keys-lost is supported on the 2005 GMC Canyon. Immobilizer generation on this platform: PK3/PK3+ / PEPS. Adding a key (with a working key already in hand) is also supported - typically faster and less expensive than an all-keys-lost reset. Submit the VIN and we will confirm the procedure and quote before scheduling.
Which modules on a 2005 GMC Canyon can you actually service?
We program, clone, repair, or replace the full programmable-module stack on a 2005 GMC Canyon. For this vehicle our database documents:
- 2 engine control (ECU/PCM)
- 2 transmission control (TCU/TCM)
- 1 body control (BCM and related)
- 3 ABS / brake control (EBCM)
- 1 immobilizer / security
- 2 key & fob
- 2 steering angle sensor (SAS)
- 1 ADAS module
Send the VIN and the operations performed and we will confirm support and pricing.
Additional Module Part Numbers
Additional OEM-sourced part numbers for the 2005 GMC Canyon covering ADAS, ECU/PCM, BCM, TCU/TCM, SRS, ABS/EBCM, instrument cluster (IPC), gateway, and steering angle sensor modules when available. These reference numbers assist technicians with module identification and sourcing prior to programming.
- ECU / PCM Part Numbers
- 19209821
- TCU / TCM Part Numbers
- 24227223, 24227226
- SRS / Airbag Module Part Numbers
- 15239331, 15239332, 12249529, 12249539, 12249549, 12249559, 15779005, 10368336, 10368760, 20864450, 25980812
- Transmission Control Module (TCM) Part Numbers
- 24227223, 24227226
Part numbers are OEM base references. Verify exact suffix via VIN-specific build data before ordering. Core Auto Logic provides mobile programming services for all listed modules in the DFW area.
Different trim or build?
Send your VIN and we'll confirm exact module support and pricing in the quote response.
Hit a security wall? We've got the keys.
1-year unlimited warranty on every flash and calibration.
Shared module fitment
Vehicles sharing modules with the 2005 GMC Canyon
These vehicles use one or more of the same replacement modules indexed for this vehicle.