VIN / Build Split
VIN pos 4-8 identifies body/engine/restraint. Ford uses World Manufacturer Identifier 1FA (passenger), 1FT (truck). Position 7 = engine code. Position 10 = model year code.
3,200+ Vehicles Supported
1-Year Unlimited Guarantee
DFW Mobile Service
DFW Serving Dallas / Fort Worth
2009 Ford Explorer Supported Services
2009 Ford Explorer
ADAS calibration, module programming, and security relearns
Trims: Base, XLT, Limited, ST, Timberline, King Ranch, Platinum. Co-Pilot360 Assist 2.0 on Limited+.
Technical snapshot
- Platform U251 (4th Gen, 2006-2010)
- CAN Architecture HS-CAN (500 kbps) - ISO 15765-4 compliant; OBD2 DLC Pin 6/14
- Security Ford PATS Gen 4-5 (Texas Instruments DST-80 80-bit transponder); SecuriLock immobilizer; no OBD PIN extraction; AKL requires FDRS PIN or dealer authorization
OVERVIEW
Expert ADAS calibration, module programming, and diagnostic recovery for the 2009 Ford Explorer. On this vehicle we cover documented systems include Rear View Camera and Blind Spot Monitoring, this U251 (4th Gen, 2006-2010) platform vehicle, PATS / Smart Key immobilizer support. Mobile across the DFW Metroplex; mail-in module work is temporarily unavailable.
Platform
U251 (4th Gen, 2006-2010)
Production
2006-present
Trim Levels
Trims: Base, XLT, Limited, ST, Timberline, King Ranch, Platinum. Co-Pilot360 Assist 2.0 on Limited+.
Drivetrain
RWD / AWD / 4WD
Engine
-
CAN Speed
HS-CAN (500 kbps) - ISO 15765-4 compliant; OBD2 DLC Pin 6/14
YEAR-SPECIFIC NOTES
Exact-year service summary for 2009 Ford Explorer
Electronic systems coverage
This 2009 Ford Explorer page does not list sensor-system records yet; module, security, and programming support is confirmed by VIN before service.
View systemsProgrammable modules
This page indexes 14 programmable module records across SRS, ECU, BCM, TCU/TCM, ABS, and SAS coverage.
View modulesGateway and security
This page includes 3 gateway, immobilizer, or key-security records for this 2009 Ford Explorer.
View securityCore Auto Logic capability
Core Auto Logic supports exact-year diagnostics, module programming, and security-access planning for the 2009 Ford Explorer using the documented module data on this page.
Choose a sectionWhat changes on this exact year
Feature availability
Immobilizer: PATS / Smart Key - Standard; Platform: U251 (4th Gen, 2006-2010) - Confirmed
Driver-assist suite
No full ADAS suite - pre-Co-Pilot360 generation. Optional rear camera; Blind Spot Information System optional on upper trims; no standard Automatic Emergency Braking.
VIN and build split
VIN pos 4-8 identifies body/engine/restraint. Ford uses World Manufacturer Identifier 1FA (passenger), 1FT (truck). Position 7 = engine code. Position 10 = model year code.
Infotainment context
Ford SYNC 1 (4.2" display); voice commands; Bluetooth; USB/Aux
Network and access
CAN: HS-CAN (500 kbps) - ISO 15765-4 compliant; OBD2 DLC Pin 6/14
Tool access for this exact year
Representative tool access paths for this exact model year, gated by the vehicle data and source packet we currently trust.
Factory scan, coding, and calibration access
Ford IDS / Ford FDRS
Factory routines and secure server authorization control this path when aftermarket coverage is not enough for the VIN.
OEM subscription required
Make-level OEM tool map plus exact-year gateway and ADAS fields.
Ford-family configuration and service functions
FORScan
Useful for supported configuration and diagnostics; factory programming still moves to OEM software when required.
FORScan Ford, Mazda, Lincoln, and Mercury support documentation.
ADAS scan, setup, and verification
Autel, Launch Tech, Topdon
Used where aftermarket coverage supports the procedure; OEM software remains required for locked factory routines.
Tool subscription required
Service-level scanner-vendor source packet plus exact-year ADAS records.
Bench cloning and chip-level recovery
Alientech / Autotuner / Orange5 / Scanmatik / Flex / VVDI2 / PCMFlash / CGDI / X-Prog
Used only when the module, donor data, EEPROM, MCU, or crash-data workflow requires bench or chip-level handling.
Bench/chip-level only
Bench programmer source packet plus exact-year module/security records.
Choose a section to view data
SUPPORTED SYSTEMS
What we service on this vehicle
Documented module coverage for the 2009 Ford Explorer. Counts reflect modules our techs have programmed or calibrated on this exact platform.
Engine / ECU Programming
2 modules documented
Powertrain reprogramming, calibration updates, replacement ECU configuration and security access.
Open Modules tabBCM / Body Programming
1 module documented
Body control module, gateway and accessory programming. Includes feature-bit reconfiguration.
Open Modules tabTCU / Transmission
1 module documented
Transmission control module reprogramming, adaptive learning reset and replacement TCM clone.
Open Modules tabSRS / Airbag Reset
1 module documented
Crash-data clear, hard-code reset and replacement airbag module configuration.
Open Modules tabABS / Brake Module
3 modules documented
ABS / EBCM bleed support, replacement module coding and yaw-rate sensor calibration.
Open Modules tabKey Security & Immobilizer
1 module documented
Immobilizer modules, key/fob types, add-key + all-keys-lost (AKL) capability and security overview.
Open Security tabIPC, SAS & Other Modules
2 modules documented
Instrument cluster cloning, steering angle sensor calibration and other supporting modules.
Open Modules tabConnectivity & Accessories
4 modules documented
Infotainment radio, surround view, remote start, trailer brake controller and other equipped systems.
Open Modules tabNeed something not listed? Most undocumented modules can still be programmed.
Feature availability 2
Immobilizer: PATS / Smart Key
StandardKey programming requires manufacturer-level tool access. Add key supported. All keys lost (AKL) supported.
Platform: U251 (4th Gen, 2006-2010)
ConfirmedVerify platform code matches when cross-referencing part numbers across model years.
WHAT WE RESOLVE
Common issues on this vehicle
Common Ford Explorer issues we resolve on this platform: Rear View Camera and Blind Spot Monitoring recalibration after windshield/bumper/suspension/CCM service. Module programming for replacement ECU/PCM, BCM, TCU, or accessory modules - U251 (4th Gen, 2006-2010) platform uses HS-CAN (500 kbps) - ISO 15765-4 compliant; OBD2 DLC Pin 6/14. Key programming and immobilizer faults - PATS / Smart Key immobilizer; all-keys-lost supported.
ADAS CALIBRATION MATRIX
ADAS systems on this vehicle
No full ADAS suite - pre-Co-Pilot360 generation. Optional rear camera; Blind Spot Information System optional on upper trims; no standard Automatic Emergency Braking.
Scroll for part numbers and Details
| System | Type | Category | Cal. Type | Supported | Part # | Actions |
|---|---|---|---|---|---|---|
| Rear View Camera | Rear Camera | Camera | None | Conditional | - | |
| Blind Spot Monitoring | Radar | ADAS | None | Conditional | - |
ADAS SYSTEM
YES Supported
Identification
- System type
- Module category
- Sensor location
Part Numbers
- OEM
- Alternative
Calibration & Triggers
- Calibration type
- Programming approach
- Requires PMI
- Trigger events
Technical Notes
- Chip / MCU
- Service notes
Need this calibrated?
WHEN IS CALIBRATION REQUIRED?
Triggers for ADAS recalibration
PCM Replacement
IDS as-built data download + PATS parameter reset required.
ABS Module Replacement
IDS ABS bleed procedure + WSS relearn.
SRS MODULES
SRS Modules
Restraint Control Module (RCM) 6L24-78043B13-AJ
- PART
- 6L24-78043B13-AJ
- LOCATION
- Under center console
- MFG
- Autoliv
- NOTES
- Requires FDRS or J2534 for RCM configuration. As-built data recommended for programming. DTC B1231 common post-crash. Module must be configured to VIN.
ECU MODULES
ECU Modules
Engine Control Module (ECM) - 4.0L SOHC V6 Cologne 9L2A-12A650-ED
- PART
- 9L2A-12A650-ED
- PROTOCOL
- J2534
- CODING
- Yes
- CLONE
- No
Engine Control Module (ECM) - 4.6L 3V SOHC Modular V8 9L2A-12A650-GC
- PART
- 9L2A-12A650-GC
- PROTOCOL
- J2534
- CODING
- Yes
- CLONE
- No
- NOTES
- fs1inc lists GC (hardware 9L2A-12B684-CA) and HG (hardware 9L2A-12B684-DA) for 2009 Explorer 4.6L; GH suffix also cited for Sport Trac.
BCM MODULES
BCM Modules
BCM (Body Control Module)
- NOTES
- Ford BCM. IDS/FDRS programming after replacement. PATS relearn required if equipped.
TCU / TCM TRANSMISSION MODULES
TCU / TCM Transmission Modules
TCU - 6R80 6-Speed Auto 8L2P-14C336
- PART
- 8L2P-14C336
- PROTOCOL
- J2534
- CODING
- Yes
- CLONE
- Yes
- CHIP/MCU
- NXP MPC5553
- NOTES
- Ford IDS required. Mercon SP ATF. 6R80 for 4.6L V8 models. TCM relearn via drive cycle.
ABS / BRAKE MODULES
ABS / Brake Modules
ABS/ESC Control Module (ABSCM)
- NOTES
- Ford ABS module. IDS bleeding procedure after replacement. Wheel speed sensor relearn.
Wheel Speed Sensor - Front (each)
- NOTES
- Hall-effect sensor. Replace if DTC C1145/C1155 set.
Wheel Speed Sensor - Rear (each)
- NOTES
- Hall-effect sensor.
OTHER MODULES (IPC, SAS)
Other Modules (IPC, SAS)
Steering Angle Sensor (SAS)
- CODING
- Yes
- NOTES
- INTEGRATED (clock spring / steering column module
Steering Angle Sensor (SAS)
- CODING
- Yes
- NOTES
- cross-year extension)
CONNECTIVITY & ACCESSORIES
Connectivity & Accessories
APIM - SYNC 4 (8-inch) LB5T-14G370-AE
- PART
- LB5T-14G370-AE
- NOTES
- Wireless CarPlay/Android Auto. FDRS PMI + FORScan As-Built.
APIM - SYNC 4 (10.1-inch portrait, Platinum) LB5T-14G370-BF
- PART
- LB5T-14G370-BF
- NOTES
- 10.1-inch portrait. FDRS PMI. Coaxial cable to IPMA must be seated.
IPC (Instrument Panel Cluster) LB5T-10849-AE
- PART
- LB5T-10849-AE
- NOTES
- FDRS PMI. Mileage in BCM.
Power Steering Control Module (PSCM) LB5T-3F641-AE
- PART
- LB5T-3F641-AE
- NOTES
- FDRS PMI + steering angle calibration.
KEY SECURITY & IMMOBILIZER
Key Security & Immobilizer
- System PATS / Smart Key
- Add Key Yes
- All Keys Lost Yes
Ford PATS Gen 4-5 (Texas Instruments DST-80 80-bit transponder); SecuriLock immobilizer; no OBD PIN extraction; AKL requires FDRS PIN or dealer authorization
IMMOBILIZER MODULES
Immobilizer Modules
PATS (Passive Anti-Theft System)
- NOTES
- Ford PATS Gen 4-5. PCM-integrated. IDS parameter reset for AKL. No OBD PIN extraction.
KEY & FOB TYPES
Key & Fob Types
PATS Transponder Key (80-bit TI chip)
- NOTES
- Cut and program. IDS PATS relearn or aftermarket tool (Autel MaxiIM). Max 8 keys.
Remote Key Fob (RKE)
- NOTES
- 315MHz Ford RKE. Program via IDS or 8x on/off cycle for simple fobs.
Replacement Notes
PATS / Smart Key system. FDRS required for key programming and module replacement. No obd pin extraction; akl supported.
ARCHITECTURE & CONNECTIVITY
Architecture & Connectivity
- Body Construction
- High-strength steel / aluminum mixed unibody; RWD architecture (AWD available)
- OBD Protocol
- ISO 15765-4 CAN (500 kbps)
- CAN Architecture
- HS-CAN (500 kbps) - ISO 15765-4 compliant; OBD2 DLC Pin 6/14
- Infotainment
- Ford SYNC 1 (4.2" display); voice commands; Bluetooth; USB/Aux
- OTA Capable
- No
- ECU/TCM Unlocking
- Contact us
- ECU/TCM Flashing
- Contact us
FREQUENTLY ASKED QUESTIONS
FAQ
How much does ADAS calibration cost for a 2009 Ford Explorer?
ADAS calibration pricing for a 2009 Ford Explorer depends on which of its 2 documented systems need work after a repair. This vehicle is documented with Rear View Camera and Blind Spot Monitoring. We provide a fixed quote after confirming the operations performed - send the VIN, the repair scope (windshield R&R, bumper work, alignment, collision), and any DTCs so the quote response can include a real number.
Can you reset the airbag light on a 2009 Ford Explorer?
Yes. The 2009 Ford Explorer uses a factory SRS control module that we support. We read and clear stored crash data, then restore the module to factory status so the airbag warning light goes out and the system returns to full operation. Reference part number on this vehicle: 6L24-78043B13-AJ. Mobile diagnosis and programming are the active service path. Mail-in bench intake is temporarily unavailable. Send the part number and a description of what triggered the light, and we will provide a quote and scheduling window.
What is needed after replacing the windshield on a 2009 Ford Explorer?
After windshield replacement on a 2009 Ford Explorer, Rear View Camera rely on the forward-facing camera and require recalibration before the systems return to operation. We perform the calibration on-site in the DFW Metroplex with OE target fixtures. Mail-in intake is temporarily unavailable.
How long does a 2009 Ford Explorer module service take?
Most 2009 Ford Explorer onsite jobs are typically scheduled within 24-48 hours once vehicle readiness, access, and route timing are confirmed. This vehicle has roughly 14 programmable modules documented in our database (2 ECU, 1 BCM, 1 TCU, 3 ABS, plus IPC/SAS/gateway/accessory). Mobile module work and ADAS calibration are scheduled in the DFW service area after quote review. Mail-in module intake is temporarily unavailable.
Do you cover the 2009 Ford Explorer on-site, or is this mail-in only?
We run a mobile unit across the DFW Metroplex for on-vehicle work (ADAS calibration, key programming, IMMO pairing, post-repair recoding, and supported module work). Mail-in module intake is temporarily unavailable. Quote the work and we will confirm the active service path for the 2009 Ford Explorer. Do not ship a module unless support confirms next steps.
What kind of warranty do you offer on 2009 Ford Explorer programming?
Every programming, cloning, and calibration job on the 2009 Ford Explorer is backed by a workmanship warranty covering the scope of work we performed: 1-year unlimited on all flashes, clones, and ADAS calibrations. If a module we programmed or a calibration we performed fails to function as expected, return it and we restore it at no charge. The warranty covers our work; it does not cover unrelated mechanical or electrical failure of the module itself.
Can you program a 2009 Ford Explorer with no working keys (all-keys-lost)?
Yes - all-keys-lost is supported on the 2009 Ford Explorer. Immobilizer generation on this platform: PATS / Smart Key. Adding a key (with a working key already in hand) is also supported - typically faster and less expensive than an all-keys-lost reset. Submit the VIN and we will confirm the procedure and quote before scheduling.
Which modules on a 2009 Ford Explorer can you actually service?
We program, clone, repair, or replace the full programmable-module stack on a 2009 Ford Explorer. For this vehicle our database documents:
- 2 engine control (ECU/PCM)
- 1 transmission control (TCU/TCM)
- 1 body control (BCM and related)
- 3 ABS / brake control (EBCM)
- 1 immobilizer / security
- 2 key & fob
- 2 steering angle sensor (SAS)
- 2 ADAS module
Send the VIN and the operations performed and we will confirm support and pricing.
Additional Module Part Numbers
Additional OEM-sourced part numbers for the 2009 Ford Explorer covering ADAS, ECU/PCM, BCM, TCU/TCM, SRS, ABS/EBCM, instrument cluster (IPC), gateway, and steering angle sensor modules when available. These reference numbers assist technicians with module identification and sourcing prior to programming.
- ECU / PCM Part Numbers
- 9L2A-12A650-ED, 9L2A-12A650-GC
- TCU / TCM Part Numbers
- 8L2P-14C336
- SRS / Airbag Module Part Numbers
- 6L24-78043B13-AJ
- Transmission Control Module (TCM) Part Numbers
- 8L2P-14C336
Part numbers are OEM base references. Verify exact suffix via VIN-specific build data before ordering. Core Auto Logic provides mobile programming services for all listed modules in the DFW area.
Different trim or build?
Send your VIN and we'll confirm exact module support and pricing in the quote response.
Hit a security wall? We've got the keys.
1-year unlimited warranty on every flash and calibration.
Shared module fitment
Vehicles sharing modules with the 2009 Ford Explorer
These vehicles use one or more of the same replacement modules indexed for this vehicle.